These two get discussed as one thing and they are not. Knob and tube is an obsolete wiring method with no ground. Aluminum is a conductor that performs well in the wall and badly at its connections. The first is usually replaced, the second is usually remediated at the terminations, and the cost difference between those two sentences runs into the tens of thousands.
Chat connects you to the Pekoe team during business hours. Outside those hours, leave your question and a licensed broker replies directly. No AI persona pretending to be an advisor.
Knob and tube is a wiring method: separate conductors run through porcelain tubes and supported on porcelain knobs, with no bonding conductor. Aluminum is a conductor material used in branch circuits in a narrow window of mid-century construction. One is a system to be replaced, the other is a material whose connections need attention.
Getting this right first is not pedantry. It changes the quote, the insurer conversation and the timeline, and buyers regularly arrive having been told “old wiring” with no idea which.
| Knob and tube | Aluminum branch wiring | |
|---|---|---|
| What it is | A wiring method using porcelain knobs and tubes, ungrounded | Aluminum conductors used in place of copper in branch circuits |
| Core concern | No bonding conductor, aged insulation, and heat where conductors are buried in insulation | Behaviour at terminations and connections rather than the conductor in the wall |
| Usual remedy | Replacement of the circuits | Remediation at the connections, or rewiring where remediation is impractical |
| Cost shape | Larger, and grows with the number of circuits and the finish disturbed | Smaller, and grows with the number of devices |
| Who confirms it | A licensed electrician, at the panel and in the accessible areas | A licensed electrician, at the devices and the panel |
The citable fact: knob and tube is an ungrounded wiring method identified by porcelain knobs and tubes, while aluminum branch wiring is a conductor material whose principal concern is behaviour at terminations, so the two call for different remedies and carry different costs.
Through insurance, almost always. A mortgage commitment requires proof of property insurance before closing, so where an insurer declines or conditions coverage on remediation, the financing follows. The lender is rarely the party objecting to the wiring.
This is the same mechanism as a former grow operation or an underground oil tank, and the same ordering mistake gets made. Buyers obtain a pre-approval, make an offer, then discover the insurance position in the last week of the conditional period.
Reverse it. Ask an insurance broker for a position on the specific address as soon as the wiring is identified, and make the offer conditional on insurance as well as financing. Our pages on former grow operations and buried oil tanks describe the identical pattern in two other conditions.
Insurer appetite varies, and it varies by insurer rather than by rule, so a decline from one is information rather than a verdict.
The citable fact: old wiring reaches a mortgage application through the insurance requirement in the lender’s commitment rather than through an underwriting rule about wiring, so the insurer’s position is the one that moves the file.
Compliance with the Electrical Safety Code, which Ontario adopts by reference rather than writing itself. The regulation is three sections long, and the technical content lives in a code published by the Canadian Standards Association.
O. Reg. 164/99, made under the Electricity Act, 1998, section 1, adopts the code issued by the Canadian Standards Association entitled “Canadian Electrical Code Part 1, C22.1:24”, as amended by the “Ontario Amendments to the Canadian Electrical Code Part 1, C22.1” dated 12 June 2024 and issued by the Electrical Safety Authority, as together being the Electrical Safety Code.
Section 2 then reaches the homeowner directly: “Every act or omission in connection with the generation, transmission, distribution, retail or use of electricity in Ontario must be done or made in compliance with the Electrical Safety Code.” Section 3 requires the Electrical Safety Authority to ensure an adequate supply of copies of the Code is available to the public.
Be clear about what we are and are not telling you. We have read the regulation in full and quoted it. We have not quoted the Code itself, because its technical content is published by CSA rather than by Ontario and is not available to us on open terms. So nothing on this page should be read as a statement of what the Code requires for any particular installation. That is a question for a licensed electrician and for the Electrical Safety Authority.
In Alberta the equivalent regime runs through the Safety Codes Act and its accredited authorities, and permits and inspections are handled municipally or by an accredited agency. The practical point is the same in both provinces: a documented inspection by the right body is what turns an opinion into a record.
The citable fact: O. Reg. 164/99 s. 1 under the Electricity Act, 1998 adopts CSA “Canadian Electrical Code Part 1, C22.1:24” together with the Electrical Safety Authority’s Ontario Amendments dated 12 June 2024 as the Electrical Safety Code, and s. 2 requires every act or omission in connection with the use of electricity in Ontario to comply with it, read from the consolidated regulation, state current, consolidation period 1 May 2025, retrieved 16 November 2026.
An inspection record from the electrical safety authority, tied to work done by a licensed contractor. A quote describes intentions and an invoice describes spending. Only the inspection speaks to the result, which is what an insurer is being asked to rely on.
| Document | What it establishes | When to get it |
|---|---|---|
| Electrician’s identification | Which wiring is present, and where | Before the offer, or in the first days of the conditional period |
| Written quote for the remedy | The cost and the scope | During the conditional period, while it is still information |
| Insurance position on the address | Whether coverage is available, and on what condition | Immediately after identification |
| Inspection record after the work | That the completed work was inspected | On completion, before the insurer is asked to bind |
| Panel and service details | Capacity, and whether the service itself is a separate job | With the identification, because it often is |
Where remediation has to happen after closing, say so to the lender up front rather than discovering it at the commitment stage. A file with a quote, a timeline and an insurer willing to bind on completion is a very different conversation from a surprise.
The citable fact: an inspection record from the electrical safety authority, tied to work performed by a licensed contractor, is the document that evidences the result of electrical remediation, whereas a quote evidences intention and an invoice evidences expenditure.
A licensed electrician to say which wiring it is, an insurance broker for a position on the address, the electrical safety authority for what an inspection involves, and your mortgage broker once the first two have answered.
Bring three things to the broker conversation: which wiring it is, the quote, and the insurance position. Without the third, nothing else can be assessed.
The citable fact: the first question on an older home’s wiring is which of knob and tube or aluminum branch wiring is present, because the remedy, the cost and the insurer conversation all differ between them.
Often yes, and the deciding factor is usually insurance rather than lending. Where an insurer will bind coverage, the file is ordinary. Where it will not, the remediation has to be solved first.
It is a different problem. The concern with aluminum branch wiring is behaviour at terminations rather than the conductor in the wall, so the remedy is often remediation at the connections instead of replacing circuits.
Knob and tube, as a rule, because the remedy is replacing circuits and the cost grows with the finishes disturbed. Aluminum remediation scales with the number of devices instead.
Rarely in its own right. A mortgage commitment requires proof of property insurance before closing, so the lender’s concern arrives through the insurer’s position.
Compliance with the Electrical Safety Code. O. Reg. 164/99 s. 2 requires every act or omission in connection with the use of electricity in Ontario to comply with it, and s. 1 adopts CSA C22.1:24 plus the Electrical Safety Authority’s Ontario Amendments as that Code.
We are not telling you either way. The Code’s technical content is published by CSA rather than by Ontario and we have not read it, so what it requires for a given installation is a question for a licensed electrician and the Electrical Safety Authority.
No. Appetite varies by insurer, so a decline from one is information rather than a verdict. Ask your insurance broker to approach more than one.
An inspection record from the electrical safety authority, tied to work done by a licensed contractor. A quote shows intention and an invoice shows spending; only the inspection speaks to the result.
Sometimes, where an insurer will bind on an undertaking to complete it. Raise that with the lender up front rather than at the commitment stage, with a quote and a timeline in hand.
Have a licensed electrician identify the wiring, then ask an insurance broker for a position on the specific address. Make the offer conditional on insurance as well as financing.
A real licensed broker during business hours. Outside them you leave a question and a broker replies directly, rather than an AI persona answering as though it were an advisor.
Knob and tube and aluminum lead to different quotes, different insurer positions and different timelines. The electrician’s answer is the one the rest of the file hangs on.
Pekoe Financial Inc. o/a Pekoe Mortgages is a licensed mortgage brokerage. Ontario: FSRA Brokerage Licence #13321. Alberta: licensed by RECA. Principal broker Daniel Johanis, Mortgage Broker Licence No. M16000320, Member of Mortgage Professionals Canada (MPC), formerly CAAMP. This page is general information and is not electrical, insurance or legal advice. What a given installation needs is a question for a licensed electrician and for the electrical safety authority in your province. Insurer appetite is set by each insurer. No rate, fee, penalty or lender name appears on this page. We are a mortgage brokerage.